Light up Toyota emblem led logo, work for the front grill or tailgate, unscratched, sealed, add a customized feel to your vehicle, Increase the visibility of your car, and give your car a glowing impressive look.
Light Up Toyota Emblem works for the front grill or tailgate, is unscratched, and sealed, adds a customized feel to your vehicle, Increases the visibility of your car, and gives your car a glowing impressive look.
Unique Design: This product is designed for car modification enthusiasts. When the lights are not lit during the day, there is no difference from the original car mark. When the license plate lighting is on at night, the LED lights will also light up, making the marker dazzling at night, and your car get eye-catching.
Applicable to TOYOTA: Work on 12V, Illuminated Toyota LED badge Light with excellent Quality， this product has the same appearance as the original car standard and can be installed in the front grill or tailgate of the car to directly replace the original car standard. Its special vacuum plating technology ensures not only the same gloss as the original logo but also high transparency and uniform brightness.
Install: There is a self-adhesive on the back, a Red wire to the battery+, black wire to the battery-. strong and durable! Built-in LED lights, especially waterproof and dustproof! The life of LED lights is up to 100,000 hours
High Quality: Adopting high-quality LED light set, high brightness, and long service life. Special waterproof and dustproof design to ensure long-term use.
You can choose the following dimensions according to your original badge size:
Rear Badge dimension:
3.94×2.68 inch (10 x 6.8 cm) Fit for Corolla 2003-05, Reiz 2011, New Vios, RAV4
4.33×2.95 inch (11 x 7.5 cm) Fit for Crown, Corolla, Yaris, Reiz 2005-09, Vios 2002-08, Avalon
4.72×3.15 inch (12 x 8 cm) Fit for Camry 2014-, Yaris,2014-,Corolla 2007-11,Levin,Rav4 2014-
5.12×3.50 inch (13 x 8.9 cm) Fit for Camry 2006-2013, Yaris (before 2013),
WISH, Previa 2017
Front badge dimension:
5.51 x 3.94 inch (14 x10 cm) Fit for Camrys 2009-2013, EZ, Corolla 2017-, old Reiz, Vios 2006-2007, Yaris 2014-,
5.91 x 3.94 inch (15 x 10 cm) Fit for New Reiz, Yaris Before 2013, Alrhard, New Vios
6.30 x 4.33 inch (16 x 11cm) Fit for Prado, EZ, VIGO, Highlander, RAV4, Avalon, Camry 2014-
Package Includes:1* Light Up Toyota Emblem
Please prepare the following tools before starting:
- Flathead screwdriver 2. Phillips screwdriver 3. Insulating tape 4. Towel 5. Pliers
【Installation Tips】
- First lay a towel next to the car logo on the trunk, and use a flat-head screwdriver to pry the car logo. The purpose of laying the towel is to prevent the car body from being scratched.
- Pay attention to peeling off the double-sided tape from the car body first. When prying, use moderate force, not too hard. Pry it off bit by bit and slowly, and clean the double-sided tape on the car logo and the body.
- Use a Phillips screwdriver to remove the partition inside the trunk. Note that there are clips in some places. Be careful when removing the sound insulation board to see various circuits.
- Now install the car logo light. Pass the power cord of the car logo light through one of the car logo positioning holes and insert it into the car compartment. Tear off the single-sided tape on the back of the light up toyota badge While pulling the wire, stick the emblem light to the car body and press it. tight.
- The light up toyota emblem is installed, now connect the power supply. The car logo light should be connected to the power supply of the rear license plate lighting so that when the night light is turned on, the car logo light will also turn on at the same time. Find the power connector of the rear license plate light.
- Unplug the plug first, peel off a hole on each of the positive and negative poles to expose the wire core, press red to red, black to black to connect the wires, don’t forget to wrap them with insulating tape, and finally plug the plug back in! Reinstall the trunk lid sound insulation panel.
Return details:
Light up Toyota badges aren’t regular products, if you require the emblem to be 100% suitable to your cars and vehicles, we apologize that this item is not suitable for you, we created this symbol according to the original badge, but it still has little distinction from your initial emblem, like clips.
We will test the products before shipping, after sending out the package, we can’t accept Refunds and Returns due to the wrong size. If the product has a quality issue, you can contact us.
It is very important to measure and check the dimensions of your original badge before making an order.
